• Hull Deck and Cockpit

• Lifetime warranty on stringers and transom
• Ten-year limited hull warranty
• Exclusive design protected hull with “Reverse Sheer”™
• Hand laid composite construction – NO WOOD
• Custom colored two-tone hull (choice of 175 different gel coat colors)
• Premium gel coat finish, formulated to provide superior weather (UV) resistance and
gloss retention
• Low maintenance, skid resistant surfaces molded into deck, cockpit, and hatches
• Push pole holders (set of three, flush mount, flip-up)
• Anodized aluminum poling platform with non-slip steps and two welded "tulip" style rod holders
• Nine (9) storage compartments with superior fit and finish hatches
• All hatches have deep gutters to ensure true dry storage
• Flush mounted, recessed stainless steel hinges on all hatches
• Stainless steel lift rings with cams on hatches
• All hatch lids are sealed with a rubber gasket trim for moisture and noise reduction
• All Hatches have a stainless steel cable restraint strap
• Heavy-duty 1/2" stainless steel bow and transom lifting eyes with backing plates
• Three stainless steel "pull-up" cleats
• Large bench seat (20” x 67”) with a “flip/flop” marine grade naugahyde cushion with
removable backrest
• Recessed, 1” stainless steel passenger hand rails
• Self-draining cockpit with dual brass overboard drains with stainless steel clamshell covers
• High-impact, snag-free, UV resistant rubrail
• Under gunwale rod racks on both sides (holds 4 rods per side)
• Four stainless steel flush mount rod holders mounted
 on deck cap

• Console

• 13&1/2" knobbed stainless steel steering wheel with flat
spokes and fingertip grips
• Fold down and pull out acrylic, lockable console door
• Four (4) cockpit courtesy lights (mounted on each side of console and under deck cap)
• Lighted, waterproof, console switch panel with
resettable breakers
• Anodized aluminum console grab rail (fits over winshield)
• 42 quart removable "Frigid Rigid" cooler with seat and backrest cushion
• Anodized aluminum console rod holders (holds 3 rods per side)
• Console windshield with custom 3/8" (acrylic) tray
• Molded-in toe space under console
• Ritchie flush-mount lighted compass

• Mechanical Systems

• Hydraulic steering with bend restrictor fittings on all hoses
• 55 gallon aluminum fuel tank
• Flush mounted, stainless steel fuel fill and vent
• Double clamps on all fuel hoses
• Fuel filter/water separator
• Automatic/Manual bilge pump with heavy-duty float switch

• Electrical System

• 12 volt socket
• Dual commercial duty marine cranking batteries with holding trays
• Dual battery switch (1-2 All-Off)
• Marine tinned, color coded wiring encased in flexible marine conduit
• Lighted, waterproof, console switch panel with resettable breakers
• 4” diameter rigging tube under console
• 3/4" diameter rigging tube under starboard gunwale (to accommodate navigation lights and trolling motor wiring)
• Battery compartment below console to accommodate trolling motor batteries
• Low profile 360 degree anchor light
• Flush mounted, stainless steel “shark eyes” type navigation lights
• Trolling motor pre-rig

• Livewell and Plumbing System

• All thru-hull fittings are high quality stainless steel
• All thru-hull fittings near or below waterline are equipped
with easy access bronze ball valve
• Rugged composite plastic drains in bait and storage wells
• All livewell and drain hoses are reinforced non-collapsible vinyl
• 34 gallon livewell/release well equipped with 700GPH heavy-duty baitwell
pump and livewell light
• Baitwell pickup and intake strainer made of marine bronze
• All compartments are insulated and plumbed overboard (nothing drains to bilge)
• Livewell intake filter with removable screen
• Two 15 gallon baitwells with livewell lights